57.75 mm Supercharger Drive Pulley
187 mm Supercharger Crank Pulley
APR presents the 3.0 TFSI Supercharger Drive and Crank Pulley Upgrades.
APR’s Supercharger Drive and Crank Pulley Upgrades dramatically increase horsepower and torque by increasing the rotational speed of the factory supercharger. APR’s Stage II Pulley ECU Upgrade makes the necessary engine management adjustments to handle the increased supercharger speeds, and in turn allows the engine to create more power. The pulleys are sold separately, allowing for multiple levels of performance, each of which builds upon the other. Finally, when combined with APR’s Ultracharger Throttle Body Upgrade in a dual pulley setup, the system is alleviated of power robbing inlet restrictions, allowing the engine to achieve exciting new levels of performance!
APR’s Supercharger Drive Pulley Upgrade decreases the diameter of the factory pulley from ~63.25mm to 57.75mm, which in turn spins the supercharger ~9.5% faster. This results in a healthy bump in horsepower and torque across the entire RPM range with the supercharger operating at a higher rate of speed. The pulley is CNC machined from billet stainless steel, e-coated black for an OEM appearance and is press fitted to the factory supercharger unit.
Gain over Stock
Gain over Stock
|- APR recommends and tuned with Sunoco GT 260 for 100 AKI mode and Sunoco GT 260 Plus for 104 AKI mode. Never use lower octane than specified by the mode.|
|- Max increases are based on APR's actual measured stock values and not those reported by Audi. | RON = ROW Fuel Grades | AKI = North American (RON+MON)/2 Fuel Grades.|
|- Reported wheel figures measured using APR's in house dynos using SAE J1349 correction and an average of multiple runs for all figures. Crank figures are estimated based on the measured wheel figures and APR's engine dyno results. Results will vary depending upon environmental conditions, vehicle, transmission, vehicle health, operating conditions, temperatures, fuel grade, dyno type, dyno setup, other variables and other modifications. For the best results, APR recommends removing the intake snow screen.|
|- Please note, transmission software is required to achieve power figures past the factory redline.|
|Audi S4/S5 (B8) (333HP)|
|Stage 2 Single Pulley||91 AKI / 95 RON||437 HP||386 FT-LBS||+94 HP||+68 FT-LBS|
|Stage 2 Single Pulley||93 AKI / 98 RON||455 HP||395 FT-LBS||+112 HP||+82 FT-LBS|
|Stage 2 Single Pulley||100 AKI / 104 RON||473 HP||404 FT-LBS||+130 HP||+95 FT-LBS|
|Stage 2 Single Pulley||104 AKI / 108 RON||480 HP||409 FT-LBS||+138 HP||+100 FT-LBS|
|Stage 2 Dual Pulley||91 AKI / 95 RON||445 HP||412 FT-LBS||+100 HP||+80 FT-LBS|
|Stage 2 Dual Pulley||93 AKI / 98 RON||465 HP||428 FT-LBS||+120 HP||+97 FT-LBS|
|Stage 2 Dual Pulley||100 AKI / 104 RON||513 HP||459 FT-LBS||+168 HP||+126 FT-LBS|
|Stage 2 Dual Pulley||104 AKI / 108 RON||527 HP||469 FT-LBS||+182 HP||+136 FT-LBS|
|Audi S4/S5 (B8.5) (333HP)|
|Audi A4/A5/Q5 (272HP)|
|Audi SQ5 (354HP)|
|Audi A6/A7 (C7) (310HP)|
|Audi A6 (C6) (290HP)|
This upgrade is only applicable to superchargers with a pressed on pulley as shown here.
|Model||Engine||Transmission||Supercharger Pulley||Crank Pulley||Dual Pulley|
|Audi A4 - (B8.5 Typ 8K)||3.0 TFSI||All||Available||Available||Available|
|Audi A5 - (B8.5 Typ 8T)||3.0 TFSI||All||Available||Available||Available|
|Audi A6 - (C6 Typ 4F)||3.0 TFSI||All||Available||Available||Not Available|
|Audi A6 - (C7 & C7.5 Typ 4G)||3.0 TFSI||All||Available||Available||Available|
|Audi A7 - (C7 & C7.5 Typ 4G)||3.0 TFSI||All||Available||Available||Available|
|Audi A8 - (D4 Typ 4H)||3.0 TFSI||All||Available||Available||Available|
|Audi Q5 - (B8 Typ 8R)||3.0 TFSI||All||Available||Available||Available|
|Audi Q7 - (MK1 Typ 4L)||3.0 TFSI||All||Available||Available||Not Available|
|Audi S4 - (B8 & B8.5 Typ 8K)||3.0 TFSI||All||Available||Available||Available|
|Audi S5 - (B8 & B8.5 Typ 8T)||3.0 TFSI||All||Available||Available||Available|
|Audi SQ5 - (B8 Typ 8R)||3.0 TFSI||All||Available||Available||Available|
|VW Touareg - (MK2 Typ 7P)||3.0 TFSI||All||Available||Available||Available|
|APR Supercharger Drive Pulley - (57.75 mm)||MS100135||$224.99|
|APR Supercharger Crank Pulley - (187 mm)||MS100133||$399.99|
A new Supercharger Belt is required.
|Supercharger Belt - For use with an APR Drive Pulley & an OEM Crank Pulley||RS100001||$19.99|
|Supercharger Belt - For use with an OEM Drive Pulley & an APR Crank Pulley||RS100003||$19.99|
|Supercharger Belt - For use with an APR Drive Pulley & an APR Crank Pulley||RS100002||$19.99|
APR Stage II software is required to run any upgraded Pulley configuration and is sold separately
|IMPORTANT PRICING AND AVAILABILITY DETAILS:|
|- Pricing: Please contact us for pricing outside the USA.|
|- Availability Compatibility: Stages, programs, and features may not be available for all ECUs.|
|- ECU Revision Notice: Multiple ECU revisions exist for each platform. APR software may be temporarily unavailable when factory updates are applied. We can check availability in person, or over the phone if the ECU boxcode/revision is known.|
|Upgrade from APR Stage I to APR Stage II||$324.99|
This product is designed for use with APR's S Tronic TCU Upgrade, NGK BKR9EIX plugs gapped @ .024” +/- .002” torqued to 30Nm and a new supercharger belt. The APR Supercharger Cooling System is highly recommended and required with the dual pulley setup. IAT’s must be below 75c to achieve the advertised power figures. A high flow intake system is highly recommended and is required to meet the advertised power figures on the A4/A5/S4/S5/Q5/SQ5. For the best results, APR recommends removing the intake snow screen.
The factory supercharger drive pulley is pressed on to the supercharger's input shaft. It's not possible to remove the factory pulley without damage, or damaging the supercharger itself unless special care and attention is taken.
The APR Supercharger Drive Pulley Installation Kit is designed to encapsulate the entire pulley and pull evenly across its entire surface. The unit is compact enough to not require complete removal of the front end of your vehicle, reducing labor time. Furthermore a provision was made to incorporate a 1/2 inch drive breaker bar which allows the entire assembly to be easily counter-held and ultimately makes the process a one man job.
A complete install manual covers the install process from start to finish, making installation easily completed at any APR dealer or in your own garage.
|APR Supercharger Drive Pulley Removal Tool.||MS100025||$224.99|